A 2.4Ghz Vertical Collinear

A 2.4Ghz Vertical Collinear
Antenna for 802.11 Applications


By Brian Oblivion and Capt.Kaboom
modified by Richard A Wenner

Introduction

The collinear antenna was historically used by base station sites, stacking various 1/2 wave dipole elements on top of each other for increased gain connected by some equipment to correct for phase error between the elements of the array. The higher in frequency the better in gain you can achieve in a relatively small assembly. The eight element array built here will yield 6dBi gain in a radome of less than a meter.

There are 3 main sections to this antenna. Starting from bottom to top of the antenna, they are the RF connector/decoupler section, the elemental array section, and the quarter-wave whip section at the top of the unit.

Equipment and Materials Needed

Components:

2 meters LMR-400
2 12" length of 5/16 K&S brass tubing
1 12" length of 11/32 K&S brass tubing
1 block of wood of at least (3.52ft) 1m long
4 1" x 2" scrap wood blocks (or approximates)
1 1/64th (2mm) thick piece of scrap metal
1 brass toilet overflow tube ( EXACT DIMENSIONS NEEDED)
1 US Quarter (or brass disk of equivalent measurements)
solder (non-acid core plumbing solder)
flux paste

Tools:

Required:
---------
utility knife
hacksaw
High-wattage soldering gun (>260Watt)
metal ruler (Metric/English)
metal sandpaper
metal file (s)

Would make life MUCH easier:
----------------------------
hand-held pipe cutter
rotary coax cutter
vise (small)
micrometer (optional)
'Dremel' tool with metal grinding/cutting heads or metal grinder


Calculations

First determine how much gain you would like the antenna to have. This will determine how many elements you will need to construct. Choose from the following table:



Gain Number of Length of
in dB elements Antenna (cm)

--------------------------------------------------------------------------------

3.5 4 32
6 8 56
9 18 116
10 21 134


For our initial experimentation we decided to build the 8 element 6dB gain antenna.

We chose LMR-400 as it was lying on the floor the night we decided to construct the antenna. LMR-400 coax has a velocity factor of %85, mostly due to it's semi-rigidness and foam dielectric. LMR-200 would be the ideal choice, as it has a smaller diameter dielectric, thus requiring a smaller diameter brass tubing. This makes sense, as the max ERP out for 802.11 is under 1W.

The antenna is designed to optimally operate at the center of the 802.11 2.4GHz band. The center of the band is determined by the following:


802.11 frequency range: 2.4000GHz to 2.4835


low_freq - high_freq
center freq = ------------------------
2


2.4000 - 2.4835
center freq = ------------------------
2


center freq = 2.441GHz


The center operating frequency is then used in the following formula to determine the length of the individual antenna segments:


( c / fc )
segment length = ------------------------ * Vo
2

Where: c = speed of light in metres per second
fc = center freq.
Vo = velocity of coax

In our example:

c = 300000
fc = 2441000000
Vo = .85

( 300000 / 2441000000 )
segment length = -------------------------------------- * .85
2

segment length = 52.2 mm

NOTE: This is the length of the antenna segments. The actual brass elements are 8mm shorter than this number, to account for the antenna segment spacing. (See diagram below).



Measurements



Figure 1. Antenna segment measurements.


The schematic of the electrical components of the antenna is displayed in Figure 2. Note: this schematic is for an eight element collinear array. The 1/2 wavelength and 1/4 wavelength measurements calculated above are to be applied to the various elements in this schematic.




Figure 2. Electrical schematic of the collinear array.


Construction

We found that it was easier to cut coax and brass in batches, as you don't have to constantly adjust the micrometer.

Coax Preparation:

Coax length should be calculated in the following way:


coax length = 1/2 wavelength + 15mm


For coax: If you are not using a micrometer, but have access to a vise, mark the proper length (67.2mm) of the coax on the vise with a piece of tape. Align the "cut" end of the coax with the measurement indicated by the tape on the vise. The end of the vise is where you make the cut. (see how it's done). It may be easier to mark multiple sections for later cutting in a batch process.


Use the coax cutter or a 'Stanley' knife to cut the marked sections, and out


and strip away the cladding,

braid



and the foil.
Remove 10mm of cladding from each side the coax segment.

Set aside and prepare the rest of the segments.

Don't forget that the final element of the array is a 1/4 wave element. Cut a segment of coax to fit the 1/4 wave element as well.






Mark off first 44.2mm segment of the 5/16" brass tubing. Using a circular pipe cutter, set the wheel of the cutter on the side of the mark to make the element a bit longer than the 44.2mm measurement. Cut the brass by moving the cutter in a circular motion around the brass tubing, slightly tightening the wheel with every three or four revolutions. Repeat until all uncut 5/16" brass tubing is exhausted.

Again, don't forget about the final 1/4 wave element! Cut a length of brass accordingly.

Element assembly:

Pair up each of the brass tubing and coax segments.



The 5/16" brass tubing fits snuggly over the LMR-400 foam dielectric. Slip a brass element over each coax segment. Slowly twist the brass tubing as you pass it over the dielectric, until it is in place with an equal amount of exposed dielectric on each side of the tubing, as below.









Figure X: Diagram of completed element assembly.

If you think you have the dexterity to solder the elements without the use of a jig, or you plan on only making one or two of these antenna's, then skip the Jig construction and jump ahead directly to the element soldering section.

Jig Construction:

Constructing a jig will help with the construction of the antenna.



Even when not building multiples, the jig really helps when trying to solder the individual elements together.

Our jig was constructed out of 5ft long 1x2 inch scrap pine wood. a section of the wood was cut to make the four guiding posts used to "hold" the antenna elements in place when soldering together. You will need 10 nails and some scrap metal approx 1/16th thick (same thickness of the brass tubing). Metal PC slot fillers work well, and can be filed down to the proper width. Please refer to Figure 2 and 3 while reading the assembly instructions for visual assistance.


Step 1: Obtain a 5 foot long 1x2 inch scrap pine wood, 10 finishing
nails and 1 PC expansion card slot filler.

Step 2: Cut a 1 inch section off of the end of the 1x2 board,
resulting in a 1x1x2 piece of wood.

Step 3: Cut the 1x1x2 wood into 4 separate equal pieces.

Step 4: Drill two holes into each of the 4 wood pieces to
accommodate the finishing nails. Make sure the hole you
drill is not too large, as we only want to avoid splitting
the wood when driving in the nails.

Step 5: Cut away the excess metal from the PC expansion slot
filler, leaving a two inch long piece of metal. File away
one side (or a little of both) to 8mm, and drill two holes
into the metal to accommodate two finishing nails. These
nails will be used to attach the metal to the large piece
of wood.

Step 6: Attach the piece of metal 3 1/4 inches from one end of the
large piece of wood.




Step 7: Arrange two of the antenna elements in the jig. Use this as
a guide for where to attach the wood blocks to the large
piece of wood.

That's it!


Element soldering:

Element soldering is pretty straight forward. Don't dink around with little 8 US dollar soldering irons for this. You need a high-wattage soldering gun for this job. Spend the $30, it is a worthy investment, and purchase the proper tool for the job. If you built the jig, follow the instructions in Step 7 of the proceeding section. See how easy it is to do it in the jig? If not, then you'll be performing a balancing act, and I hope you have a steady hand.




When soldering the final element(1/4 wave element), remember that the center conductor is bent over and soldered to it's own brass tubing. When completed, it should look like below.







Note: Be careful when applying the heat to the brass elements. It doesn't take much time to generate enough heat to begin to melt the foam dielectric.

Solder all the elements at this point before proceeding to the next section. This is what your element array should look like.




Quarter Wave Whip Assembly:

The 1/4 wave whip assembly slides over the end of the last element of the antenna. See Figure 4 for exact measurements. Because the center conductor of the last element is soldered to the elements brass tubing, the top of the bend of the center conductor will be an arbitrary length unique to each antenna. The important thing here is for the top of the whip to be 1/4 wave in length from the end of the foam dielectric of the last element. Line up the 1/4 wave next to the last element and determine the length the notch will need to be.



Figure 4: Quarter Wave Whip Measurements and position

Cut out the notch to accommodate the soldered center conductor of the last element. If you are really slummin', use a hacksaw and file to make the notch. After the notch is cut and burrs are filed away mount the 1/4 wave whip on the end of the last element.




Decoupling and RF Connector Assembly:

The decoupling section is a bit involved, as it requires drilling a hole into a US Quarter, or similarly sized slug, and using a propane torch to solder it to the decoupling brass tubing.

There are two parts to this assembly. First, there is the feed-line element, constructed in the same manner as the antenna elements. Second, is the decoupling sleeve, mounted over the feed-line element.

The decoupler sleeve is constructed out of 1" brass tubing equal to 1/4 wavelength, a length of 11/32" brass tubing at least 1/4 wavelength, and 1 US Quarter with a center-drilled hole to accommodate the 11/32" brass tubing.



Above is picture of the 1/4 wavelength 1" brass tubing with the 11/32" brass tubing soldered into the center of the US quarter along side. Below is the fully assembled unit from the top and bottom







Figure X. Diagram of decoupling sleeve

The feed-line is similar in construction to the antenna elements. The difference is the coax is of much longer length than the 5/16" brass tubing. The coax is prepared in a much different fashion since we solder the braid of the coax to the end of the brass tubing 1/4 wavelength up from the end of the N connector. Below this, the cladding remains intact and terminates in the N connector assembly. The brass tubing must be cut so that at least 1/2 wavelength of 5/16 brass tubing is between the end of the decoupler sleeve assembly and the 1st antenna element (see diagram). It must also accommodate the length of the decoupler sleeve assembly plus allowing a length for tuning of the sleeve to the feed-line (this is done my sliding the sleeve up and down over the feed-line tubing). In our example, the coax was 10.8cm(4 1/4"), and the 5/16" brass tubing was 6.8cm (2 11/16"), in length.

When completed it should look like this:-



As part of the final assembly it looked like this:-




Tuning and final assembly

Tuning:

Unfortunately, without a spectrum analyzer or SWR/Power meter one cannot optimally tune the antenna, but one can coarsely tune it using the Linux wireless tools and two wireless NIC's. By adjusting the decoupling sleeve, you will notice a change in the RSSI reading as you slide the decoupling along the feed-line element. Adjust until you reach a peak in the RSSI in the receiver. Only take measurements when not touching the antenna, and always return to a similar position when taking a reading. Your body changes the RF characteristics of the room you are working in. Once the antenna has been properly matched, fix the decoupler in place with a bead of solder and proceed to the next section.

Radome construction:

Outdoor electrical UV resistant conduit was used for the radome. It was cut to the appropriate length to accommodate the entire array, leaving the female N connector hang out the bottom by 1/2 inch. The array is held in place with plumbers epoxy. We used a PVC cap to cover the top, but it could have been sealed with plumbers epoxy as well. Using double sided sticky tape, the array is held in place at two locations within the tube.




Figure X: diagram of finished antenna in radome.

Good luck!